Air-Conditioning Systems (Part 2)

Thermostats
Thermostats are devices designed to control the heating and cooling system in the home so that the air temperature remains comfortable. Homeowners should understand how thermostats operate, as well as the more common problems associated with them.
Thermostats…

Air-Conditioning Systems (Part 2)

THERMOSTATS

 

Environmental Services Company

 

Thermostats are devices designed to control the heating and cooling system in the home so that the air temperature remains comfortable. Homeowners should understand how thermostats operate, as well as the more common problems associated with them.

 

Thermostats can be manually controlled or set to activate automatically based on timers or room temperature readings. Most thermostats contain two meters: the “set” temperature that the thermostat is asking for, and the actual temperature. On a traditional dial-type thermostat, the user can increase the set temperature by rotating the dial clockwise and lower it by rotating it counter-clockwise. Newer thermostats usually have digital displays, which can be used to adjust automated heating and cooling schedules.

 

Location
In order to avoid false or “ghost” readings, which will cause unnecessary furnace or air-conditioner cycling, the thermostat must be installed so that it correctly reads the room temperature.

 

The following locations may cause the thermostat to give false readings:

  • near a heat source, such as a fireplace, hot water pipes, bright lights, direct sunlight, and electrical appliances that produce heat
  • in a drafty hallway, or near a window or exterior door that is left open often; and on an outside wall.
  • Outside walls are affected too much by outside temperatures, which may make the thermostat “think” the air in the house is warmer or cooler than it really is.

 

Common Thermostat Problems and Solutions

  • erratic operation or fluctuating temperature. This is often caused by poor pin connections between the thermostat and the backplate when the backplate is flexed against an uneven wall. To allow the backplate to flatten out, loosen the screws that attach the backplate to the wall, then snap the thermostat back onto the backplate.
  • a thermostat that doesn’t respond to changes in room temperature. This can happen when there is air passing over the temperature sensor from a hole in the wall behind the thermostat, through which wires enter from the air-handling unit. To rectify this, insulate the hole behind the thermostat with fiber insulation, spray foam, or any other insulating material.
  • a temperature reading that is inaccurate. A convenient way to test the temperature sensor is to tape a thermometer to the wall next to the thermostat and wait 15 minutes. A faulty thermometer needs to be recalibrated. Instructions for recalibration vary by manufacturer.
  • loss of power. This may be caused by the following two situations:
    1. If the air handler powers the thermostat, check the circuit breaker meant for the air handler and make sure it has not tripped.
    2. If batteries power the thermostat, make sure they are lithium, not alkaline. Alkaline batteries will die rapidly or cause erratic thermostat operation.

 

Maintenance and Other Tips

  • Give the thermostat’s interior a light dusting with a small, soft-bristle paintbrush. Canned air can also be used to blow off dust. Twist the screws to remove the cover. Be sure to clean the contacts, which are small metal plates within the unit. The wires coming from the transformer attach to the contacts. Do not touch any of the interior parts with your fingers.
  • If the base is loose, re-tighten the screws. Check the wires coming from the transformer. If any corrosion is present, remove the wire from the contact and clean it. Use a wire stripper to remove the surrounding insulation, cut back the wire, and reconnect it.
  • Make sure the terminal screws are tight.
  • For wireless thermostats, make sure the model number of the thermostat matches the model number of the receiver. If the model numbers don’t match, the thermostat and receiver will not be compatible and won’t function properly together.
  • Make sure that your thermostat has been set to the proper position for the season: cooling or heating. The air conditioner will not run with the switch set to “heating” and, conversely, the heating system won’t run if the thermostat has been set to “cooling.”
  • Thermostats that contain a mercury switch must remain perfectly level or they may not control the temperature setting.

 

A Few Notes on Energy Savings
Many people believe that furnaces work harder than normal to warm an area back up to a comfortable temperature, which will counteract energy savings gained from turning the thermostat down. This belief is a misconception that has been disproved by years of studies and research. Fuel is saved between the time the temperature is stabilized at the lower level and the next time heat is needed, while the fuel required to re-heat the space is roughly equal to the fuel saved while the building drops to a lower temperature.

  • According to the U.S. Department of Energy, consumers can save 10% on their utility bills by setting their thermostat lower by 10° to 15° for eight hours. This can be easily accomplished with a programmable thermostat.
  • Be careful not to set the thermostat so low in the winter that indoor plumbing pipes freeze, or so low during the summer that mold may be allowed to grow prompted by excess indoor humidity.

 

Programmable Thermostats
Using a programmable thermostat in the winter, you can automatically turn down your heat at night or when you’re not at home. In the summer, you can save money by automatically turning your air conditioner up at night or when you’re at work.

 

Using a programmable thermostat, you can adjust the times that the heating and air conditioner go on and off according to a preset schedule. As a result, the equipment doesn’t operate as much when you’re asleep or when the house (or a part of it) is empty. Programmable thermostats can store and repeat multiple daily settings (six or more temperature settings a day) that you can manually override without affecting the rest of the daily or weekly program.

  • Archive

  • TRUST THE BEST…

    Residential Inspection Company
    Structural engineering company

    SUPERIOR SERVICE FROM CERTIFIED
    TECHNICIANS WITH SUPERIOR TRAINING

    NO MATTER WHAT SERVICE YOU NEED
    WE SIMPLIFY THE PROCESS!

    Copyright 2009 – 2019 GreenWorks® Service Company | All Rights Reserved
    Texas Real Estate Commission Consumer Protection Notice

    2019-09-09T08:42:18+00:00Jul 15, 2018|GreenWorks Inspections|0 Comments